IDX-PRO+VDI

[ashefr10]

hello, here are 2 videos showing how to idx. All metals in the first and the mode discrimination seoncde set to eliminate small nails and aluminum foil. If someone could help me pinpoint mode I threshold sound continuously when I approach a currency threshold disappears so I can pinpoint the run but as soon as I remove the threshold sound currency returns . the rest of the detector is operated. The THRESHOLD does not seem to be really on the operation.

http://www.youtube.com/watch?feature=player_embedded&v=aXo3hC4Dz18

http://www.youtube.com/watch?feature=player_embedded&v=cqSs4ldH2YI

[onuba]

hello, for stability if you toujour the same problem, read the post 1252 edouardo R25 therefore advised to remove your resistance adjusted and put a 4k7 resistor between terminals 6 and 7 of the LM393 (IC4)

The same thing was happening my, and remove the r25 resistance and places a resistance of 4k7 between the terminals 6 and 7 of the LM393 (IC4) And a nice sound has now

[ashefr10]

ok , pinpoint work? On my map I pinpoint mode continuous beep and when I approach a currency near the coil sound aténue and returns.

The same thing was happening my, and remove the r25 resistance and places a resistance of 4k7 between the terminals 6 and 7 of the LM393 (IC4) And a nice sound has now

[Leshka]

I do elips. TX 36 coils, 0,6 mf. RX 270 coils, 40 nf. Normally or not?

[onuba]

ok , pinpoint work? On my map I pinpoint mode continuous beep and when I approach a currency near the coil sound aténue and returns.

I have the same problem pimpoit it sounds when withdraws the currency,
And THRESHOLD is like a volume does not manage to remove
Touching cables, potemsimetros pita idx me does not work very well resistance 4k7 does not convince me 4k7 only it does tone THRESHOLD work

[onuba]

THRESHOLD looks like a volume

Problem pimpoit pita when withdraws the currency, and the THRESHOLD looks like a volume touches cables and sounds of potemsimetros, idx does not work very well.Help Help

[onuba]

pimpoit pita when withdraws the currency

Idx pro was working correctly it is possible that screw vr3 on having touched it is desplasado phase?

[ashefr10]

hello , problem in mode PP , I made a video trying to show the problem.

http://www.youtube.com/watch?v=z2LeJUw1dzc

[Davor]

How about you first set the offset properly?

[ashefr10]

I found my fault, I reversed two resistors R34 and R35, 22k and 220k, I also put a bad value for the capacity c29 10 uF instead of 100 uF. thank you for your help. thanks

[onuba]

solved potencimetro geb defective,Separated sensibility of ensendido

[onuba]

tones does not work

Electronic shop me vendio tc4024bp serves for tones pedi cd4024 ,Help

[ashefr10]

hello , mode pp work ! Hi, I noticed that the ferrous Mode pinpoint sounds not really. When I approach a ferrous and does not sound as soon as I remove the ferreur against sound by sound. you have this problem? for everything other metals such as bronze or other not no problem

[ashefr10]

hello, I put at disposal of the idx 2 videos, the first fashion discrimination and pinpoint the second mode.

http://www.youtube.com/watch?feature=player_embedded&v=6X2bbkKphk8

http://www.youtube.com/watch?feature=player_embedded&v=oKu2QW24tOg

[onuba]

2k2 in vr3

I have put 2k2 in vr3 and one it sees the improvement and pinpoit that This sees beyond, Without the balance sheet of ferrita since I do not have tendre that to search, to coil 8 " concentric 30cm